Steps for an Oil Tank Installation
You’ve finally decided to install an oil tank on your property. Here’s how to properly install the tank, including getting a permit, supporting the tank, and installing the piping. This article will walk you through the process step-by-step. Then, you can begin enjoying the benefits of using a tank for more information about it try to visit or inquire about oil tank installation westchester county ny .
Properly install an oil tank
You need to know how to install an oil tank properly. There are several factors to consider, including the location of the tank, the previous use, and the surrounding environment. Please make sure the tank is at least five feet away from any fuel-fired appliances, and the tank should be installed so that there is plenty of room to check it thoroughly. If the tank is near walls or floors, allow four inches of clearance from the floor and tank bottom.
Installing an oil tank requires two types of pipe. You can use a 2-inch black iron pipe or galvanized steel pipe. The pipe should be installed at least six inches above the ground and 24 inches above the tank. Use high-quality pipe dope on all fitting connections, including the pipe going into the tank. For safety, you can install a vent alarm on the line to prevent oil leaks. Once the oil tank is installed, it is essential to inspect the tank for leaks and cracks.
Get a permit
If you want to install an oil tank in your home, you need a permit. This document, which is usually blurry, shows where to install the oil tank. The tank size is on the permit to the right, along with where you will place it. If the tank is underground, the letter “X” indicates it must be underground. Then you will need to get a plumber’s permit, which requires you to use a licensed plumber.
Once you have the permit, you must find out if the oil has contaminated your property. You may be able to tell if there is contamination by the appearance of soil and a sheen on groundwater. You can also get samples taken from the site to see if it is safe for drinking water. To save money, make sure you contact your oil company first. This company will often do the sampling for you, and it is also recommended that you ask your contractor to write a letter report to show that the oil tank was removed. In addition, homeowners should take pictures of the tank and have their contractor write a letter stating that the oil tank is no longer present on their property. This will be useful for homebuyers who want to know that the tank is not in their home.
Properly support the tank
During the installation process, ensure the oil tank is level and positioned correctly. Check for signs of shifting or stress in the previous oil tank. If this is the case, you may want to put a concrete slab or firmer ground under the new oil tank. Additionally, consider the tank’s proximity to a building or tree trunks. Once you know that these aspects are addressed, it will be easier to support the tank properly.
First, a technician must cut a rectangular opening on the side of the oil tank. A metal cutting blade is used to cut, but the personal protective gear is recommended. A Sawzall(r) fitted with a coarse metal blade can be used to create a large working opening. The technician should make sure the cut extends above the end of the oil tank to avoid spilling oil on the floor.
Install the piping
Before you begin installing the piping for an oil tank, you should determine the type of surface you need. In some cases, it will need to be elevated and/or firm. If the tank was previously on a different surface, it might be necessary to install a new concrete pad. Whether you use a standard asphalt driveway or a poured concrete pad, make sure you use a good quality pipe dope. You may also want to add alarms to the tank.
The fill line for an oil tank is located at the opposite end of the supply connection pipe. This is the pipe that will fill the tank with oil. Typically, this is made of galvanized steel and two inches in diameter. The fill line must be fitted with a fill cap. The vent line is located next to the fill line and is approximately one and a half inches in diameter. Again, it is important to install the piping according to the local codes and specifications.
Protect the tank from falling debris
There are several ways to protect an oil tank from falling debris. One option is to use a rain cap. This will prevent water from getting into the tank and can prevent spills. Additionally, you can use a home heating fuel additive to displace water and avoid sludge. Fuel companies often add this additive to fuel tanks, but you can also request it if you have a specific problem. Another option is to purchase a water absorber product that drops into the tank and is removed at the end of the day.
Regardless of your situation, protecting the oil tank from falling debris is important. If you live in a cold climate, clear the area around the tank of snow and ice. Also, ensure that the roof is clear of any obstructions, such as tree branches or fallen trees. Be sure to check the oil tank frequently and take measures to protect it from falling debris. While you’re at it, be sure to check for signs of damage and do not push or pull on fragile parts.
Install the vent line
If installing an oil tank inside your home, you should first install the fill line. This piping is about two inches in diameter and is made from galvanized steel. Installing the fill line requires placing a cap on the outer end of the pipe. In addition, you should install a vent line adjacent to the fill line hole. Installing the vent line is as simple as following the installation instructions.
You can install a vent alarm in any above-ground oil tank to warn you of possible leaks. A vent alarm is an audible whistle that emits a whistle while filling the tank. When the oil reaches the whistle’s tip, the fill pipe will shut off, preventing a spill. A vent alarm is also helpful for monitoring the level of oil inside the tank. It will alert delivery people to the need to refill the tank.